Analysis of free vibration of nano plate resting on Winkler foundation
Piyush Pratap Singh^{1} , Mohammad Sikandar Azam^{2} , Vinayak Ranjan^{3}
^{1, 2}Department of Mechanical Engineering Indian Institute of Technology (ISM), Dhanbad, Jharkhand, India
^{3}Department of Mechanical and Aerospace Engineering, Bennett University, Greater Noida, Uttar Pradesh, India
^{1}Corresponding author
Vibroengineering PROCEDIA, Vol. 21, 2018, p. 6570.
https://doi.org/10.21595/vp.2018.20406
Received 19 November 2018; accepted 26 November 2018; published 13 December 2018
JVE Conferences
Present paper deals with the vibration analysis of nano plate supported by Winkler foundation using Eringen’s elasticity theory with Classical Plate theory. RayleighRitz method has been employed in this study for finding frequencies of plate subjected to different edge conditions. The obtained results are first tested for convergence and then validated with the published literature. Further study is carried out to analyse the effect of various parameters on natural nondimensional frequencies of nano plate resting on Winkler foundation. The study reveals that the nonlocal effect has significant effect on vibration behaviour of nano plate resting on elastic foundation. Observations shows that on increasing the Winkler foundation modulus and aspect ratio the nondimensional frequency parameters increases.
Keywords: nano plate, Rayleigh Ritz method, frequency parameter, nonlocal elasticity theory, Winkler foundation.
1. Introduction
Nanoplates are the building blocks for various nanoscale objects which are called nanostructures. Recent, development of nanotechnology enables new generation devices with enhanced functionality hence playing vital roles in many engineering fields. These materials have superior properties as compared to conventional materials [1].
In recent time the nanomaterials have become the important components of different modern nanoelectromechanical systems [2]. It is thus necessary to analyse vibration behaviour in order to design nanostructures. Experimental analysis at nanoscale size is tough to carry out, hence efficient mathematical models for nanostructures analysis is needed. Vibration analysis of Nanostructures with traditional models shows that properties changes to an extent at nanoscale called size effect. When the system is reduced to nanoscale it can no longer be modelled as a continuum as systems become comparable to intermolecular spacing. If smallscale effects in Nano designing are ignored then this may lead to faulty Nano system design. Hence in order to achieve an accurate solution for correct and realistic design small scale effects must be taken into account. In order to overcome these shortcommings different continuum models as couple stress theory [3], modified couple stress theory [4], strain gradient theory [5] and nonlocal elasticity theory [6] were given. Among these thories, the nonlocal elasticity theory proposed by Eringen is mostly considered. Nonlocal Continuum mechanics theory put forward by Eringen [7] incorporates small length scale effect which plays a key role when Nano structures are taken into account. This theory is a widely used as results are found to be an accurate and quick analysis of Nano plates can be done. According to the nonlocal elasticity theory, the stress at a specific point not only depends on stress at that point but also the stresses of every points of that body. In the present work, governing equations of classical plate theory is based on nonlocal elasticity theory. Natrajan et al. [8] analysed the size effect on linear free vibration behaviour of nano plate using Erigen’s nonlocal elasticity theory. Murmu and Pradhan [9] analysed the scaling effect on vibration behaviour of nano plate using nonlocal continuum mechanics. Behra et al. [10] studied the vibration of the rectangular isotropic nano plate. Daneshmehr et al. [11] studied the vibration of functionally graded nano plate with the help of nonlocal theory. Hence it is can be seen that Erigen nonlocal theory is widely used to analyse the vibration behaviour of different nano plate structures.
Previous literature suggests that most of the studies focuses analysis of vibration behaviour of nano beams and nano plates of isotropic material plates without any interaction with foundation. Very less study is found to be conducted on analysis of plate on foundation. In number of applications Nano plates on elastic foundation, are used. Different elastic medium models for analysis of plate on elastic foundation were proposed by number of researchers. One of the reported models is Winkler model [12], which is derived from Winkler's hypotheses. This model considers vertical closely spaced linear springs as the elastic medium. This model is considered as building block and is easy to solve.
According to literature many authors have tried to solve the problem using a different method as Finite Element Method, Differential quadrature methods etc. It is to be noted that when the plate is rested on elastic foundation then these methods become very difficult to solve and accurate result cannot be obtained. It can be concluded that previous methods are not efficient for analysis of plate resting on Winkler foundation. In present article, authors have obtained the accurate solution of natural frequency with help of Kirchoff’s theory and Rayleigh Ritz method. Few studies have used this method for the analysis of large scale plate [13]. The extant literature review suggests that no study highlights in detail, the effect of various material and foundation parameters on Nano plates resting on elastic support subjected to different combinations of boundary conditions.
2. Mathematical modelling
Nano plate of dimension $a$×$b$ as shown in Fig. 1, has been considered for analysis. The edges are taken along the $x$, $y$ axes for the mathematical modelling of the Nano plate that rest on Winkler foundation. The $z$axis is considered perpendicular to $xy$ – plane.
Fig. 1. Winkler foundation supporting nano plate
According to classical plate theory, displacements of a point is expressed by equation:
where, $u$, $v$ and $w$ denote displacement in the $x$, $y$ and $z$ axes and $w$ represents a deflection along the $z$axis. Neglecting the transverse shear caused due to inplane stretching and bending, the linear strain linked with the displacement field is:
Strain energy of an elastic Nano plate is formulated as:
The effective strain energy (${U}_{eff}=U+{U}_{foundation}$) of the nano plate, on WinklerPasternak elastic foundation, is:
where, $\mu ={\left({c}_{0}{l}_{\mathrm{i}\mathrm{n}\mathrm{t}}\right)}^{2}$ [6] is the nonlocal parameter, ${l}_{int}$ denotes internal characteristic length, ${c}_{0}$ represents constant and ${k}_{w}$ shows stiffness of Winkler foundation. The kinetic energy of the nano plate on Winkler foundation in simplified form is given by:
where, ${m}_{0}$ is $\rho h$.
The harmonic type displacement components are assumed as:
where, $w\left(x,y,t\right)$, $W(x,y)$ and $\omega $ are transverse deflection, maximum deflection and frequency of free vibration of the nano plate on elastic foundation.
Now, on equating the maximum strain energy ${U}_{ef{f}_{\mathrm{m}\mathrm{a}\mathrm{x}}}$ and kinetic energy ${T}_{\mathrm{m}\mathrm{a}\mathrm{x}}$ we will get Rayleigh quotient, given by the following equations:
The maximum deflection $W(x,y)$ is the summation of the series of simple algebraic polynomials involving $x$ and $y$, presented as:
where, ${c}_{i}$ are unknown constants and ${f}_{i}$ are function generated. The functions (${f}_{i}$) contain polynomials $\varphi $ and simple polynomials ${g}_{i}(x,y)$ are represented as:
where exponents $p$, $q$, $r$ and $s$ stands for edge conditions of different edges.
Moreover, considering the partial derivative of ${\omega}^{2}$ w.r.t unknown constant and then equating it with zero, gives:
Further simplifying the Eq. (15), we get the following equation in term of Stiffness and inertia matrix:
where:
$\lambda $ is the nondimensionalised frequency parameter, and $K$, ${K}_{foundation}$ and $M$ are stiffness and mass matrices respectively.
3. Results and discussions
3.1. Convergence and validation
The frequency parameter of nano plates is analysed in detail in this section. Convergence test is carried assure the accuracy of present result. Authors further compared the obtained results with the results available in the literature. For test of convergence and comparison, the nano plate is considered to be under SSSS edge condition without foundation.
3.1.1. Convergence
Convergence of frequency parameter of nano plate subjected to various boundary conditions is shown in Fig. 2 with respect to different number of the polynomials. The figure suggests that the frequency parameter converges with increase in the number of polynomials, to the exact frequency and becomes constant after certain no. of polynomial i.e. 40 in present case.
Fig. 2. Convergence of fundamental frequency parameter of nano plate
3.1.2. Comparison
The nondimensional natural frequency is compared with Aghababei and Reddy as reported in Table 1. An excellent agreement between the results can be observed.
Table 1. Comparison of frequency parameter (${\lambda}_{m\times n}={\omega}_{m\times n}h\sqrt{\rho /G}$) of SSSS (simply supported) square plate. ($E=$ 30×10^{6}, $\nu =$ 0.3)
Frequencies

$\mu $

Aghababei and Reddy [14]

Present

${\lambda}_{1\times 1}$

0

0.0963

0.09636

1

0.0880

0.0880


${\lambda}_{2\times 2}$

0

0.3853

0.3874

1

0.288

0.2884


${\lambda}_{3\times 3}$

0

0.8669

0.8608

1

0.5202

0.51671

3.2. Parametric study
Table 2 illustrates the variation of Frequency parameter of nano plate subjected to different boundary condition and resting on elastic foundation for different aspect ratio ($a$/$b$), nonlocal parameter ($\mu $) and foundation parameters (${k}_{w}$). On analysis of the table it is observed that the nonlocal parameter plays the crucial role. With increase in nonlocal parameter ($\mu $) the nondimension frequency decreases irrespective of BCs. This is because plate becomes more flexible on introduction of small scale effect hence this effect should not be neglected.
Further it is seen from the Table 2 that for constant value of μ if aspect ratio is increased the frequency parameter increases considering specific values of foundation parameter for every BCs. This is because of the fact that, with increase in $a$/$b$ the stiffness of the plate decreases which increases the non dimensional frequency.
It is evident from Table 2 that frequency parameter increases with increase in coefficient of stiffness of Winkler Foundation for specified $\mu $ and $a$/$b$. Although the frequency parameter increases but the increment is very small. It can be said that Winkler parameter has insignificant effect on frequency parameter irrespective of BC, $\mu $ and $a$/$b$.
Table 2. Variation of frequency parameter of nano plate under different boundary condition with different aspect ratio ($a$/$b$), foundation parameter (${k}_{w}$) and nonlocal parameter ($\mu $)
BC

${k}_{w}$

Nonlocal parameter ($\mu $)


$\mu =$1

$\mu =$ 2


Aspect ratio


0.5

1

1.5

2

0.5

1

1.5

2


SSSS

0

10.0984

14.7555

21.2350

28.6250

8.7550

12.2911

16.9907

22.1922

10

10.1073

14.7616

21.2393

28.6282

8.7653

12.2984

16.9960

22.1963


100

10.1870

14.8162

21.2773

28.6564

8.8570

12.3640

17.0435

22.2327


SCCF

0

14.1635

13.7892

15.4657

17.8578

11.1517

11.6753

12.7460

14.3190

10

14.1698

13.7951

15.4715

17.8629

11.1598

11.6830

12.7530

14.3253


100

14.2268

13.8540

15.5237

17.9080

11.2320

11.7520

12.8163

14.3816


SFSF

0

2.0521

3.0454

4.2989

5.2961

1.4647

2.8003

3.8153

4.5305

10

1.6108

3.0747

4.3198

5.3130

1.5248

2.8322

3.8388

4.5503


100

2.0521

3.3272

4.5030

5.4630

1.9853

3.1044

4.0438

4.7246

4. Conclusions
The authors used the classical plate theory along with Eringen’s nonlocal elasticity theory to analyse the frequency parameter of nano plate under different combination of boundary condition that rest on Winkler elastic foundation. Effect of the aspect ratio, stiffness of Winkler foundation and nonlocal parameter on the vibration behaviour of nano plate is studied. It can be concluded from the results that nonlocal parameter has an influence on vibration behaviour of small scale plate for all considered BCs hence it should always be considered for modelling small scale plate structure. Further study reveals that frequency parameters increases on increasing aspect ratio for every BCs. It is also concluded that the effect of stiffness of Winkler foundation on vibration behaviour of nano plate is insignificant.
References
 Dai H., Hafner J. H., Rinzler A. G., Colbert D. T., Smalley R. E. Nanotubes as nanoprobes in scanning probe microscopy. Nature, Vol. 384, 1996, p. 147. [Publisher]
 Chakraverty S., Behera L. Free vibration of rectangular nanoplates using RayleighRitz method. Physica E: Lowdimensional Systems and Nanostructures, Vol. 56, 2014, p. 357363. [Publisher]
 Hadjesfandiari A. R., Dargush G. F. Couple stress theory for solids. International Journal of Solids and Structures, Vol. 48, Issue 18, 2011, p. 24962510. [Publisher]
 Nix W. D., Gao H. Indentation size effects in crystalline materials: a law for strain gradient plasticity. Journal of the Mechanics and Physics of Solids, Vol. 46, Issue 3, 1998, p. 411425. [Publisher]
 Eringen A. C. Nonlocal polar elastic continua. International Journal of Engineering Science, Vol. 10, Issue 1, 1972, p. 116. [Publisher]
 Eringen A. C. On differential equations of nonlocal elasticity and solutions of screw dislocation and surface waves. Journal of Applied Physics, Vol. 54, Issue 9, 1983, p. 47034710. [Publisher]
 Eringen A. C. Nonlocal Continuum Field Theories. Springer Science & Business Media, New York, 2002. [Search CrossRef]
 Natarajan S., Chakraborty S., Thangavel M., Bordas S., Rabczuk T. Sizedependent free flexural vibration behavior of functionally graded nanoplates. Computational Materials Science, Vol. 65, 2012, p. 7480. [Publisher]
 Murmu T., Pradhan S. C. Smallscale effect on the free inplane vibration of nanoplates by nonlocal continuum model. Physica E: Lowdimensional Systems and Nanostructures, Vol. 41, Issue 8, 2009, p. 16281633. [Publisher]
 Behera L., Chakraverty S. Effect of scaling effect parameters on the vibration characteristics of nanoplates. Journal of Vibration and Control, Vol. 22, Issue 10, 2016, p. 23892399. [Publisher]
 Daneshmehr A., Rajabpoor A., Hadi A. Size dependent free vibration analysis of nanoplates made of functionally graded materials based on nonlocal elasticity theory with high order theories. International Journal of Engineering Science, Vol. 95, 2015, p. 2335. [Publisher]
 Winkler E. The Theory of Elasticity and Strength Dominicus. Dominicus Prague, Czechoslovakia, 1867. [Search CrossRef]
 Singh Pratap P., Azam M. S. Ranjan V. Vibration analysis of a thin functionally graded plate having an out of plane material inhomogeneity resting on WinklerPasternak foundation under different combinations of boundary conditions. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 2018, https://doi.org/10.1177/0954406218796040. [Search CrossRef]
 Aghababaei R., Reddy J. N. Nonlocal thirdorder shear deformation plate theory with application to bending and vibration of plates. Journal of Sound and Vibration, Vol. 326, Issues 12, 2009, p. 277289. [Publisher]
Cited By
Mechanical Systems and Signal Processing
J. Awrejcewicz, G. SypniewskaKamińska, O. Mazur

2022

Advanced Structured Materials
Jan Awrejcewicz, Anton V. Krysko, Maxim V. Zhigalov, Vadim A. Krysko

2021

Nonlinear Dynamics
Jan Awrejcewicz, Grzegorz Kudra, Olga Mazur

2021

Journal of Computational and Nonlinear Dynamics
Olga Mazur, Jan Awrejcewicz

2020

ZAMM  Journal of Applied Mathematics and Mechanics / Zeitschrift für Angewandte Mathematik und Mechanik
Olga Mazur, Lidiya Kurpa, Jan Awrejcewicz

2020

SN Applied Sciences
Saheed Afolabi Salawu, Gbeminiyi Musibau Sobamowo, Obanishola Mufutau Sadiq

2019
